Описание пользователя

Seek advice from that product’s set up sheet for directions. Twist and remove mounting bracket to insert battery. Product Description Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive infrared (PIR) gadgets that routinely management lights by way of RF communication with a dimming or switching device. These Sensors detect the heat from people moving inside an space to find out when the area is occupied. The Sensors then transmit the appropriate commands to the associated dimming or switching device to show the lights on or off mechanically, providing each convenience and distinctive energy financial savings. Sensor doesn't carry out satisfactorily from this location, it could also be moved to 1.Four Ifanother location by pulling the Sensor straight down and repeating steps 1.Three and 1.4. 1.5 If the Sensor’s performance is satisfactory, it ought to be completely hooked up to the ceiling tile, as described in section G. Permanent Mounting. Short-term Stable Ceiling Mounting Use this procedure if the Sensor shall be mounted on a solid, steady ceiling floor akin to drywall, plaster, concrete, or wooden. Two 3M™ Command™ adhesive strips are supplied for temporarily mounting and testing the Sensor on easy, solid ceiling surfaces. These strips are designed for easy, damagefree elimination and are usually not reusable. These strips should not be used for completely mounting the Sensor (see part G. Everlasting Mounting ). Fastidiously follow the removing instructions below to ensure the ceiling just isn't damaged throughout elimination. Notice: Do not use the adhesive strips on ceiling tiles, as they'll probably trigger injury to the tile upon removal. Straightforward-to-follow Instructions Set-Up To ensure that the Sensor to function properly, it should first be set up with a corresponding dimming or switching device. The process for organising a Sensor with a Maestro Wireless® (MRF2- solely) Dimmer or Electronic Change is detailed beneath. P/N 041-172a 2.1 Peel the purple "Command Strips" liner off of one of the adhesive strips and apply the strip to the flat aspect of the mounting bracket as shown within the diagram. Notice: Do not cover the bracket’s screw holes as a result of they will be used to mark screw gap locations on the ceiling. Establishing a Sensor with a Maestro Wireless Dimmer or Electronic Swap Dimmer Key Options · Low Maintenance. 10-yr battery life. Convenient low-battery indicator. · Multiple Devices. Up to three Sensors can work collectively to manage lights for broader protection in large spaces. Each Sensor may be added to as much as 10 receiving gadgets. Sensor Operation Occupancy Model - The Sensor will routinely turn the lights on when the area is occupied and automatically turn the lights off after the house is vacated. The Sensor will automatically flip the lights off after the space is vacated. There is a built-in 15-second vacancy grace period that begins when the lights are mechanically turned off, throughout which the lights will mechanically flip again on in response to movement. This grace period is supplied as a security and comfort characteristic within the event that the lights flip off whereas the room remains to be occupied, in order that the person doesn't have to manually flip the lights back on. After 15 seconds, the grace period expires and the lights should be manually turned on. This Sensor is a part of a system and can't be used to control a load without a appropriate dimming or switching system. Consult with the instruction sheets of the receiving device(s) for installation information. The Sensor could also be put in as much as 60 ft (18.3 m) away from the associated dimming or switching device(s) if they are in direct line of sight. If there are walls or other obstacles between the Sensor and receiving machine(s), the Sensor must be situated inside 30 ft (9.1 m). Warning: This product should not be used to regulate gear which might create hazardous conditions, resembling entrapment, if operated unintentionally. Sensor in a location where it has a broad view outdoors the intended space. If this is unavoidable, the lens can be masked to block the view of undesired areas (refer to part I. Lens Masking). This warranty is in lieu of all different specific warranties, and the implied guarantee of merchantability is proscribed to at least one 12 months from buy. This warranty does not cowl the cost of set up, elimination or reinstallation, or injury ensuing from misuse, abuse, or harm from improper wiring or set up. This guarantee doesn't cowl incidental or consequential damages. LUTRON’S Legal responsibility ON ANY Declare FOR DAMAGES ARISING OUT OF OR IN CON­NEC­TION WITH THE MANUFACTURE, SALE, Set up, Delivery, OR USE OF THE UNIT SHALL Never EXCEED THE PUR­CHASE Value OF THE UNIT. This guarantee provides you particular authorized rights, and you may have other rights which range from state to state. Some states don't allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty might final, so the above limitations might not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst logo are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American Nationwide Requirements Institute. IEC is a trademark of the Worldwide Electrotechnical Commission. Made and printed within the U.S.A. 25/09/09 P/N 041-172 Rev. A 8 ft (2.4 m) 18 x 18 ft (5.5 x 5.5 m) 13 ft (4.0 m) 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.4 m) 10 ft (3.Zero m) 22 x 22 ft (6.7 x 6.7 m) 16 ft (4.9 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.Eight m) Short-term Mounting Strategies 1.1 1.2 Insert the ceiling tile mounting wire by way of the 2 smaller holes in the mounting bracket and change the mounting bracket. Mount Sensor to a ceiling tile by inserting the wire legs through the tile, ensuring the Sensor is flush to the tile. Word: Do not twist wire legs together. 1.2 After the Sensor has been temporarily mounted, depart the Sensor in place on the tile and both take the tile down or remove an adjoining tile to gain entry to the legs of the mounting wire on the again of the tile. Low Exercise: This is probably the most sensitive setting and can detect very slight motions. That is the really helpful setting, as it should work nicely for practically all purposes. It is good for areas the place occupants will often be seated for long intervals of time. Twist the wire legs collectively tightly so the mounting bracket remains snug towards the tile. This setting is barely less sensitive than the Low Activity setting and can be utilized for spaces that expertise regular activity. That is the least delicate setting and can be utilized for spaces that can usually only experience large motions, similar to foot traffic. The Low Exercise setting is the default and will perform best for many purposes. Rarely, if the Sensor is placed close to exterior noise sources akin to heating vents, air conditioning vents, or mild bulbs, it may flip the lights on without occupancy or keep the lights on too long after vacancy. If this occurs, altering the sensitivity to Medium Activity or Excessive Exercise should resolve the issue. Change the tile. Permanent Solid Ceiling Mounting 2.1 2.2 2.3 Superior Set-Up Operation The superior set-up is accessed by using the buttons on the back of the Sensor. Drill two 3/sixteen in (4.6 mm) pilot holes for the offered screw anchors. Press the anchors into the holes and faucet flush with a hammer. To show the current setting, press and launch the specified button. An LED will illuminate briefly, indicating the present setting. Place the flat facet of the mounting bracket against the ceiling and install the 2 provided screws utilizing a hand screwdriver. To adjust a setting, press and hold the desired button until the LED corresponding to the present setting begins flashing rapidly, indicating the setting can now be adjusted. Each subsequent button press of less than 2 seconds will increment the mode to the following out there setting. Pressing any of the other buttons will don't have any effect. To save the selected setting, press and hold the button until the LED turns on stable, indicating the saved setting. During the adjustment procedure, if there is no exercise for 30 seconds, the LEDs will turn off and no settings might be saved. Observe: Don't over-tighten. 2.Four Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise direction until the Sensor locks into place. To take away the bracket from the ceiling, grasp the removing tab on the adhesive strip and pull the tab VERY SLOWLY straight throughout the ceiling, stretching the strip till the bracket releases from the ceiling. Discard the strip. By no means pull the strip at an angle, as it might break or harm the ceiling surface. Word: Don't pull at an angle. Lens Masking (Non-obligatory) Whenever doable, the Sensor must be put in in a location the place it can't simply see into areas exterior the supposed space, similar to hallways or adjoining rooms. If this situation cannot be prevented, parts of the lens may be masked with the supplied labels to block the Sensor’s view of the undesired areas. It's endorsed to take away the Sensor from the mounting bracket before making use of Superior Set-Up (Optionally available) the masking labels. The Sensor features a number of advanced set-up modes. For the vast majority of installations, the default settings will present the best performance and you won't need to make the most of the superior set-up. The Occupancy version of the Sensor has three adjustable superior set-up modes: Timeout, Auto-On, and Sensitivity. The Vacancy-Solely version has solely two modes (Auto-On not obtainable). The default settings are listed beneath. The Sensor might be screwed onto the mounting bracket in several totally different orientations. Make sure to note the Sensor’s orientation earlier than taking it down and exchange the Sensor in the same orientation to ensure the supposed area gets blocked. Outer lens sections correspond to the detection areas furthest away from the Sensor, while inner sections correspond to areas nearer to the Sensor. Watch out when applying the labels to avoid creating gaps between adjoining masked sections. The Sensor could detect motion by means of inadvertent gaps. Always (Occupancy model solely) Timeout 30 min 15 min 5 min Auto-On Always Low gentle Disable Activity Timeout 30 min 15 min 5 min Superior Set-Up Modes Auto-On At all times Low gentle Disable Activity Exercise: Low Exercise Lens sections shown in white are masked with labels Timeout The Sensor will turn the lights off if no motion happens at some point of the timeout period. There are three available timeout settings: 5, 15, and half-hour. Lens Mask Lens sections proven in gray have not been masked Auto-On The automatic-on functionality of the Sensor can be adjusted to regulate how the lights reply upon initial occupancy. There are three out there settings: At all times, Low mild, and Disable. Always: The lights will always activate. Testing Sensor Coverage With the Sensor mounted on the ceiling, press and launch the "Test: Sensor" button on the entrance of the machine. The lens will glow briefly, indicating the check mode has been entered. Observe: There is a heat-up interval of approximately 40 seconds after the batteries are put in earlier than the test mode could be activated. If the button is pressed during this time, the lens will flash continuously until the warm-up interval is full, after which the test mode might be automatically entered. Affirm the protection space by walking through the house and observing the lens. The lens will glow stable each time motion is detected. If the lens remains off during movement, the Sensor cannot detect movement at that location. Press and launch the "Test: Sensor" button once more to exit the check mode. If the button shouldn't be pressed, the test mode will mechanically trip quarter-hour after being enabled, or 5 minutes after the last detected motion if the room is vacated. If the Sensor has significant trouble detecting movement in the course of the take a look at, it ought to be moved to a different location and retested. If the Sensor nonetheless has poor detection from the brand new location, consult with the Troubleshooting part. Temporary Drop Ceiling Mounting Use this procedure if the Sensor might be mounted on a ceiling tile. The ceiling tile mounting wire is supplied for both temporary and everlasting mounting of the Sensor to drop ceilings composed of a number of tiles. It's designed to allow temporary mounting, testing, and repositioning (if necessary) of the Sensor without damaging a ceiling tile. As soon as the Sensor’s ultimate place has been chosen, the mounting wire could be twisted to lock the Sensor in place permanently. If the Sensor coverage and wireless communication tests have been successfully completed, use the mounting bracket as a template to mark the screw hole areas with a pencil. Observe: Pull very slowly. Max. Room Dimensions Radius of Protection for Complete Protection at Flooring In case you are unsure about appropriately positioning the Sensor, the following non permanent mounting and testing procedures are recommended to confirm proper performance before completely installing the Sensor. Sensor’s detection vary relies on the ceiling top, as proven within the table under. Notice: Do not disassemble, crush, puncture, or incinerate the batteries. Don't dispose of batteries in regular family waste. Please recycle, take to a correct battery disposal facility, or contact your native waste disposal supplier concerning local restrictions on the disposal or recycling of batteries. O NOT mount the Sensor within four ft (1.2 m) of HVAC vents or gentle bulbs put in beneath the ceiling line. Hotter rooms might reduce the Sensor’s capacity to detect occupants. Use solely high-quality lithium batteries, measurement CR123, three V (ANSI-5018LC, IEC-CR17345). Don't use rechargeable batteries. Utilizing improperly rated batteries may damage the Sensor. For questions concerning the set up or operation of this product, call the Lutron Technical Assist Middle. Please present actual mannequin quantity when calling. U.S.A. and Canada (24 hrs / 7 days) Setting the Occupancy Light Degree (occupancy version, dimming gadgets solely) the Sensor to the mounting bracket by inserting and twisting in a clockwise 2.5 Attach path till the Sensor locks into place. Sensor coverage and wireless communication assessments as described in 2.6 Carry out sections E. Testing Sensor Coverage and F. Testing Wireless Communication. The Sensor ought to be installed in a location where it has a good view of all parts of the room. The Sensor requires line of sight to operate properly. If you cannot see the Sensor, it can't see you. The Sensor can not see by means of glass objects such as patio or shower doorways. The range and efficiency of the RF system is very dependent on a wide range of complex components akin to: · Distance between system components · Geometry of the building structure · Development of walls separating system elements · Electrical equipment situated near system parts Technical Help 2.2 Establish a location on the ceiling where the Sensor could have a good view of the room. 2.Three Take away the black "wall side" liner from the adhesive strip. The Sensor is designed for ceiling use only. Don't set up on ceilings greater than 12 ft (3.7 m) or non-ceiling surfaces. Doing so might considerably inhibit the Sensor’s performance. 4. Don't paint Sensor. · · · · The "Lights On" and "Lights Off" buttons ought to now switch the lights in the room on and off, respectively, when pressed. Repeat the above procedure to set up the Sensor with any additional devices. The Sensor is meant for indoor use solely. Function between 32 °F and 104 °F (zero °C and 40 °C). 1.1 several seconds. Sensor that has been set up. After approximately 6 seconds, the lens will flash rapidly a number of times, indicating the light degree has been saved. All Sensors set up with the Dimmer will now use the saved occupancy mild degree. 2. Clear Sensor with a gentle damp cloth solely. Don't use any chemical cleaners. Note: This gear has been tested and found to adjust to the limits for a category B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide affordable protection in opposition to dangerous interference in a residential installation. This tools generates, makes use of and can radiate radio frequency vitality and, if not installed and utilized in accordance with the directions, might cause harmful interference to radio and television reception, which may be determined by turning the tools off and on. The user is inspired to attempt to right the interference by a number of of the next measures: Reorient or relocate the receiving antenna. Increase the separation between the tools and receiver. Join the gear into an outlet on a circuit completely different from that to which the receiver is related. Seek the advice of the vendor or an experienced radio/Tv technician for assist. Caution: Modifications or modifications not expressly permitted by Lutron Electronics Co. could void the user’s authority to function this equipment. This gadget complies with Half 15 of the FCC rules. This system must accept any interference received, including interference that will trigger undesired operation. Switch 2.1 Set the Dimmer to the specified mild degree for entering the room. 2.2 Save holding the "Lights On" button on the entrance of a Be aware: For either Sensor version, the lights may also be manually turned off at any time by using the dimming or switching system straight. Necessary Notes or Add the Sensor to the Dimmer or Swap by urgent and holding the "Lights Off" button on the entrance of the Sensor for roughly 6 seconds until the lens flashes briefly. The lights in the room may also flash three occasions, indicating the Sensor has been efficiently added. The Dimmer or Change will exit set-up mode routinely. The sensitivity of the Sensor could be adjusted primarily based on the anticipated stage of activity throughout the room. There are three obtainable exercise settings: Low Exercise, Medium Activity, and High Exercise. Permanent Drop Ceiling Mounting Observe: Go away the elimination tab uncovered previous the edge of the bracket so it can be accessed for removal later. 6 seconds till all LEDs on the gadget begin flashing. Release the faucet button. Sensor is detecting motion in areas that aren't desirable, akin to hallways or adjacent rooms, discuss with section I. Lens Masking. If Sensor detection is satisfactory during this test, carry out the wireless communication test as described in part F. Testing Wireless Communication. Testing Wireless Communication This test should be performed to verify that the Sensor has been correctly set up with the corresponding dimming or switching machine and that there is proper wireless communication from the chosen Sensor location. If the lights in the room are usually not on, turn them ON manually on the dimming or switching gadget. Press and launch the "Lights Off" button on the front of the Sensor. The lights ought to turn OFF. Press and launch the "Lights On" button on the entrance of the Sensor. The lights should turn on. If the lights don't respond accurately, consult with the Troubleshooting part. Low light: The lights will only turn on mechanically upon entry if there is not already enough ambient gentle in the room. Hallway falls inside Sensor’s coverage space. Disable: This setting converts the Sensor to vacancy mode. The lights will not robotically turn on but will nonetheless mechanically turn off after vacancy. The lights have to be manually turned on by utilizing the related dimming or switching machine. Notice: The 15-second vacancy grace interval is lively in this mode. Refer to the Sensor Operation section originally of this doc for more particulars. Troubleshooting Symptom Attainable Causes Resolution Lights don't activate when house is occupied. Sensor is just not accurately added to dimming / switching gadget(s). Sensor’s Auto-On setting is set to "Low light" or "Disable". The lights had been lately turned off manually and the timeout has not yet expired. Sensor doesn't have full view of room. Sensor is outdoors wireless vary of dimming/switching device. Consult with section B. Set-Up. Consult with part H. Advanced Set-Up. Dimming/switching gadget has been improperly wired. Light bulb(s) burned out. Breaker is off or tripped. Sensor’s timeout is just too short for this application. Sensor does not have full view of room. Lens mask is improperly utilized. Sensor’s sensitivity is just too low. Sensor’s timeout has not but expired. An exterior noise source such as an HVAC vent is interfering. Check with part A. Pre-Set up. Behavior of lights doesn't match Sensor settings. Sensor coverage extends beyond room perimeter. The meant setting was not saved. A number of Sensors are added to a dimming/switching gadget and their settings don't match. Seek advice from part A. Pre-Installation. Consult with part C. Sensor Placement or I. Lens Masking. Discuss with part H. Advanced Set-Up. Check with part H. Superior Set-Up. Sensor lens doesn't glow in response to motion during Sensor protection testing. Sensor can't see movement because of obstruction. Room is too large or oddly formed. Move Sensor to another location. Check with part C. Sensor Placement. Multiple Sensors may be mandatory for full room coverage. Strive shifting Sensor to a brand new location or reducing sensitivity. Check with section C. Sensor Placement or H. Advanced Set-Up. Lights turn OFF while house is occupied. Lights keep ON after area is vacated. Lens doesn't cease glowing throughout Sensor coverage testing even when there is no movement. Lights do not respond accurately during wireless communication testing. Sensor lens flashes and lights don't activate when space is occupied. Battery has been installed incorrectly. An exterior noise source corresponding to an HVAC vent is interfering. Refer to part C. Sensor Placement. Discuss with part C. Sensor Placement or F. Testing Wireless Communication. Discuss with section H. Advanced Set-Up. Discuss with section C. Sensor Placement. Refer to section I. Lens Masking. Refer to section H. Advanced Set-Up. Consult with section H. Superior Set-Up. Try shifting Sensor to a new location or reducing sensitivity. Confer with part C. Sensor Placement or H. Superior Set-Up. Sensor will not be appropriately added to dimming / switching device. Sensor is exterior wireless range of dimming/switching device. Refer to part B. Set-Up. Move Sensor nearer to dimming/switching device and retry take a look at. Confer with part F. Testing Wireless Communication. Battery has been installed incorrectly. Dimming/switching machine has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Battery is low. Consult with part A. Pre-Set up. Take away sensor from check mode. Seek advice from section E. Testing Sensor Protection.

If you cherished this article and you also would like to obtain more info about flipboard.com nicely visit our web page.